Robo C2 Not Going Past Blue Start Up Screen

Getting Started¶

What's in the box¶

Also your new Robo R2, you will find the following in the box:

1. Quick Start Guide
2. Autodesk Fusion 360 pattern software gratuitous ane-year voucher
3. Robo stickers to place EVERYWHERE.
4. 24V power supply
5. Filament Guide Tube
6. Toolbox with the hotend cover, 2 allen wrenches, lubricant, tweezers and z-starting time calibration carte.
7. Robo USB drive
8. 300g Robo calorie-free blue filament
9. Spatula

Register your Robo R2¶

Before you start, delight register your Robo R2 for any servicing or warranty needs if they're always required. You can register your production past visiting our registration_site.

Unboxing Robo R2¶

Now that y'all've received your Robo R2, it'southward fourth dimension to unbox it and get familiar with your printer and accessories.

Your R2 is housed in 2 styrofoam pieces, secured together by a top and bottom box. Simply undo the iii clips at the bottom of the box by pinching in and pulling, then slip the acme box off.

The printer'south accessories are stored in the inclusions box within the printer. First, you will need to take off the zip tie securing the door shut to admission this inclusions box.

Now, undo the blue record and simply slide the inclusion box out.

Now we are ready to accept out the inner packing fabric.

At that place are 4 orange gantry rod holders that need to be taken off. There is one at each corner of the superlative gantry. Only push button on the clips with your thumb and they will come up off.

Next, remove the zipties securing the rods to their plastic brackets.

At present, remove the blueish tape holding the moving parts stable.

Finally, using the handholds on the bottom of your R2, lift the printer out of the bottom styrofoam piece.

Tip

Salvage your printer box, foam inserts, and inclusions box for transportation. As well, you might demand the original packaging to exercise your warranty or ship your printer in the future.

Initial set-up¶

At present let'south motion forward with your initial prepare-up of Robo R2.

Inside the inclusions box, in that location is a small toolbox; here you will find the hotend cover. Go alee and take that out and place it over the hotend. It is held in with magnets so it just pops right in.

From here you'll want to connect the power cord to the designated area on the back of the printer and and so plug it into an Ac outlet.

Now go ahead and turn on the printer.

Information technology is necessary connecting Robo R2 to your Wi-Fi network. Doing then provides you with necessary updates that allows for a more enjoyable 3D printing experience.

Annotation

You tin also use an Ethernet cable (LAN) to connect Robo R2 directly to your Wi-Fi network.

Wi-Fi Configuration¶

To begin connecting to your Wi-Fi network, Select UTILITIES on domicile screen. Select NETWORK. Select CONFIGURE WIFI. And so select your Wi-Fi network and use the on-screen keyboard to enter your password. Once you're done, select CONNECT.

Updating¶

At present, you lot will need to update Robo R2.

Select UTILITIES. Then select UPDATE.

Update to the latest version and wait about a minute to get everything upwards-to-date. If your Robo R2 is already up to date, the push button will be greyed out and say 'up to date'.

Calibration and setting Z offset¶

Adjacent you'll want to calibrate Robo R2 by selecting UTILITIES on the touch screen. Then select WIZARDS from the listing. From hither you'll select Z Showtime Wizard. Now, the printer will wait to calibrate its abode position.

Follow the directions on the screen by using the calibration bill of fare or a standard sheet of newspaper. Press on the 'Upwardly' arrow to raise the bed up toward the nozzle of the printer. Slide the calibration card in between the nozzle and bed and continue pressing the 'Up" button until you lot feel piffling resistance on the card between the Nozzle and the print bed. Note: You even so want to be able to slide the scale card back and along simply with plenty resistance that it is touching both the bed and the nozzle.

If your bed is too high and the calibration card does non accept enough room to slide betwixt the nozzle and the bed, press the down arrow until the calibration card can pass freely but with a slight resistance between the nozzle and the bed.

You tin also fine-tune your kickoff by going to Utilities> Wizards> Fine Melody Commencement

Loading filament¶

Now, unhinge the spool holder by simply pushing on the pinnacle of the higher lever from the rear of the printer. Next, insert the filament feed tube into the filament sensor block.

To begin loading filament, hang your filament spool on the top spool holder. Be sure to unroll at to the lowest degree eleven"— or 30 centimeters — of filament and cut the tip with a pair of pair of scissors. Thread it through the base of operations of the filament sensor block and into the filament feed tube.

Now select UTILITIES on the impact screen. Then select WIZARDS from the list. Finally, select FILAMENT LOADING WIZARD. The on-screen prompts should guide you to loading your filament.

Proceed feeding the filament through the filament feed tube until it reaches the extruder. Then, printing the extruder lever arm and feed the filament into the printer's gears.

The filament drive gear should push the filament down, into the nozzle, and out the other terminate. Once you see this, printing NEXT on the screen, so press Done.

The test print¶

To create your outset test print Select FILES on the home screen. And so select a file to print from the list. Now, select First to print—and be certain to wait several seconds while Robo R2 prepares to print the file.

Annotation that you can select Pause to interruption your impress, or you can select Cancel to cancel your impress.

Removing the examination print¶

When the test print is complete and cooled down, carefully remove the impress bed with both easily and set on a flat surface. Use the provided spatula to carefully remove the print at its borders. Then, slowly work your way underneath the print until it'southward loose. Don't force the print loose past pulling it upwards direct upwards from the print bed, since this may crusade your print to pause.

Using Hotspot Style¶

Your printer is capable of starting If no Wi-Fi signals are available for connexion, yous can use Hotspot Style to emit a Wi-Fi point from Robo R2 in order to connect to it wirelessly from your smart device. To access Hotspot Fashion, practise the following:

1. Select "Utilities" on the home screen of the Robo C2 touch on screen
2. Select "Network" from the list
3. Select "Start Hotspot Mode" from the list

pellparin1936.blogspot.com

Source: http://support-site.readthedocs.io/en/master/R2/getting-started/

Share this post